CiscoCCNP-BSCN(5)
添加时间: 2007-9-3 22:01:22 作者: Cisco认证考试 阅读次数:31 来源: http://www.d9soft.com
101. What command will configure the router interface to do Policy-Based Routing using Route-Map ‘Jeffrey’?
102. Which of the following are the well-known Mandatory BGP Path Attributes?
a. AS-path
b. Origin
c. Community
d. Next-hop
103. What command will change the default OSPF External type so OSPF will add up and consider all of the internal costs in the OSPF path?
104. Which of the following is true of OSPF ABR?
a. ABR’s are always in more than one area
b. At least one interface is in Area 0
c. It redistributes routing information with routers in other areas
d. All interfaces are in the same Area
105. Given the IP routes 192.168.8.0 through 192.168.15.255 for OSPF Area 1, what command will summarize all networks as a single CIDR netblock on the ABR?
106. What types of routes can an OSPF totally stubby ABR send into the stubby area?
107. Which of the following commands are necessary to create a Route Map?
a. Match
b. Set
c. seed
d. route-map
e. metric
108. What OSPF command will consolidate External routes on an ASBR?
109. What is the default administrative distance for an EIGRP external route?
a. 90
b. 100
c. 120
d. 170
110. Which of these commands is used for BGP route summarization?
a. area
b. auto-summary
c. aggregate-summary
d. aggregate-address
111. What is the procedure for setting up automatic redistribution between IGRP and EIGRP?
a. Set both processes to the same AS number
b. IGRP and EIGRP are automatically redistributed by default
c. Configure the EIGRP ABR to use the special area 0
d. Configure both processes for metric-type 1
112. You are in a UNIX area that requires RIP to be sent on the local network segments, but the customer wants to continue using their existing and fully functional OSPF network. For efficiency, you do not want to send RIP over certain interfaces connected to the backbone. Which of the following must be done to meet the objectives?
a. Use the ‘redistribute ’ command to receive OSPF and send out RIP
b. Use the ‘redistribute <#>’ command to receive OSPF and send out RIP
c. Use the ‘passive interface ’ command to stop RIP on certain interfaces
d. Use the ‘passive-interface <#>’ command to stop RIP on certain interfaces
113. On low-speed NBMA media, what is the default EIGRP hello interval (in seconds)?
a. 0
b. 30
c. 60
d. 120
114. What databases are maintained by OSPF routers?
a. LSA
b. Adjacencies
c. NLSP
d. Routing
e. Topology
115. In order for OSPF to form an adjacency with its newly discovered neighbor, which configuration parameters must match?
a. Encryption (tunnel mode)
b. Stub Area Flag
c. Authentication (type and password)
d. Hello (and dead/timeout) intervals
e. Area ID
116. Which of the following are private address ranges that are not routed on the public Internet?
a. 192.168.0.0
b. 10.0.0.0
c. 168.192.0.0
d. 127.0.0.0
e. 172.16.0.0
117. What command views the status of all OSPF virtual links?
118. What command on the ABR will make OSPF area 6 a Totally Stubby Area?
119. Which of the following best describes Type 1 OSPF LSA?
a. Router link entry/record that shows in the routing table as ‘O’
b. Autonomous System External type-1 which appears in the routing table as ‘E1’
c. Summary link entry that shows in the routing table as ‘IA’
d. Network link entry that shows in the routing table as ‘O’
120. What command will configure the EIGRP process to use a maximum 75% of all available bandwidth on Serial 0 for Autonomous System 1?
121. BGP peers are also known as______?
a. Neighbors
b. Route-Maps
c. Summaries
d. MED’s
122. What command will ensure that BGP routes are not advertised out your current interface?
123. What are some route redistribution features that you may want to enable to reduce the odds of your network’s routing protocol using less than optimal paths?
a. Route maps
b. Passive interface
c. Default gateway
d. Helper addre
ss
e. Distribute-lists
124. What command will summarize external OSPF routes on an ASBR for 192.232.0.0/16?
125. Which of the following are untrue of Route Maps?
a. When a Match is made, the Route Map can change the route with the map-tag command
b. When a Match is made, the Route Map will change the route with the set command
c. Route Maps use the Match command, similar to statements in an access-list
d. Route Maps are numbered
上一篇文章: CiscoCCNP-BSCN(4) 下一篇文章: CiscoCCNP-BSCN(6)
相关文章:
相关软件: